Comparison of All PCB Surface Finish Types - PCB Assembly

What is PCB surface finish?

 

You will get efficient and thoughtful service from CHANYEE.

PCB surface finish is between the metal face of the components and the pads on PCB, for protecting the copper foil from oxidation and providing a solderable surface for 

is between the metal face of the components and the pads on PCB, for protecting the copper foil from oxidation and providing a solderable surface for PCB assembly . Every PCB surface finish has its pros and cons, could be customized as the requirements.

HASL(Lead-free) and ENIG, OSP, Hard Gold, ENEPIG, ISn, IAg, etc.

Although, currently conventional choices of PCB surface finishes are nothing less thanand PS Electronics covers all the types of PCB surface finishes, like, etc.

This article was edited by PS electronics to guide you know every of the mianstream PCB surface finish, as below.

 

Comparison Points of PCB Surface Finishes

• Planarity&#;

• RoHS (Lead or Lead-free)

• Environment friendly

• Cost

• Shelf life

• Reworkability

 

Measurement Units of PCB Surface Finish

• Micro-inch (1μ&#;) = 0.&#; (inch)
• Micron (1μm) = 39.37μ&#; (μinch)
• 1mil = 25.4μm = 0.001&#; (inch)

 

&#; Types of PCB Surface Finish

1. Hasl/Hasl Lead-free

"The PCB is dipped into molten solder so that all exposed copper surfaces are covered, excess solder is removed by 'hot air knives'".

The composition of hasl treatment commonly is Tin (63% ) and Lead (37%), typical thicknesses range from 30- μ'', of which the melts point is about 183 degrees C.

For hasl lead-free, the common alloys refer to Sn/Ag/Cu (SAC), Sn/Cu/Co, Sn/Cu/Ni/Ge, etc., of which the thicknesses range from 300- μ''. The hasl PCBs (lead-free) even can bear a high temperature of 260 degrees C. Hasl lead-free is the predominant PCB surface finish for circuit boards for it is RoHS&WEEE compliant.

Hasl PCB finish

Pros:

• Low cost
• Widely applicable
• Easy processing
• Reworkability
• Excellent shelf life (12+ months)

• Visual inspection & testing

Cons:

• Uneven surface (solder bead)
• Not good for PTH (high thermal stress)
• Not good for thick copper boards
• HASL is unfriendly to envirronment

2. ENIG (Immersion Gold)

Two layer metallic coating - ENIG cover the copper using thick, well-electrically nickel-gold, commonly 2-8 μ'' Au over 120-240 μ'' Ni, in which nickel is deposited on palladium-catalyzed copper surfaces, gold adheres to the nickel-plated area by molecular exchange, which protects the nickel (actual solder surface) until the soldering process, also Au provides low contact resistance and good wetting.

ENIG technology answered the request for the flat surface used in fine pitch assembly and lead-free, even though it is a little bit expensive than others, but no doubt ENIG has already become the most commonly-used PCB surface finish for many categories, such as cellphone or power supply.

ENIG PCB finish

Pros:

• Flat surface excellent for fine-pitch (BGA, QFP...)
• Lead-free
• Good for PTH
• Long shelf life (about 12 months)
• Good contact resistance
• Excellent for thick copper PCBs

Cons:

• Expensive
• Black phosphorus pad
• Signal loss at high-frequency
• Electromagnetic interference
• Not re-workable

3. Electrolytic Ni/Au (Hard Gold)

The same two-layer metal coating, what differs from ENIG is that this PCB surface finish is electroplated rather than chemical immersion, in which nickel layer gets plated before gold plating. Since the PCB must act as an electrode, the electroplating must be done before the solder mask process.

Because of unstable solderability, it is currently only used in IC carrier boards (PBGA/FCBGA/FCCSP...), or in the gold finger that is explicitly required.

Pros:

• Flat surface
• Lead-free
• Excellent shelf life (12 months+)
• Especially suitable for contact switch or "gold finger"

• Good for IC carrier PCBs

Cons:

• Gold surface easy oxidizing
• Gold whiskers might cause short-circuit
• Skin effect

4. ENEPIG (Electroless Nickel/Palladium Immersion Gold)

A solution to "Black phosphorus pad" of ENIG. By introducing a layer of palladium (4 to 20 μ''), prevent Ni layer (120 &#; 240 μ'') from corroding overly by Au (2 to 8 μ''), ENEPIG got come up in the s, also brought in a better option to wire bonding.

Although ENEPIG it is not a commonly-used PCB surface finish at present, the development grows rapidly.

Pros:

• Flat surface
• Lead-free
• Excellent shelf life (12 months+)

• Good for IC carrier PCBs

• Excellently suitable for gold/aluminum wire bonding

• Forms reliable Ni/Sn solder joints

Cons:

• Expensive
• Complicated in plating processing
• Immature technology

5. OSP (Organic Solderability Preservative)

On the clean bare copper surface, a layer of organic film is chemically applied. This film is a water-based organic compound that selectively combines with copper and provides an organic metal layer to protect the copper surface from rust in the normal environment. In the subsequent soldering, it will be quickly removed.

OSP PCB finish

Pros:

• Lead-free
• Flat surface, good for fine-pitch pads (BGA, QFP...)
• Very thin coating
• Can be applied together with other finishes (e.g. OSP+ENIG)
• Low cost
• Reworkability

Cons:

• Not good for PTH
• Handling Sensitive
• Short Shelf life (<6 months)
• Not suitable for crimping technology
• Not Good for multiple reflow
• Copper will get exposed at assembly, requires relatively aggressive flux
• Difficult to inspect, might cause issues in ICT testing

6. Immersion Tin (ISn)

Tin will be applied directly on copper for protection. It does not bring in any new elements to the soldering surface, especially workable for communication backplanes. But copper and tin have a strong affinity with each other, the diffusion of one metal to another will inevitably occur, which will directly affect the shelf life. ISn requires good storage, while it is restricted due to the presence of carcinogens.

Pros:

• Lead-free
• Flat surface
• Uniform coating with superior hole wall lubricity
• Low cost
• Suitable for crimping technology
• Re-workable

Cons:

• Not good for PTH
• Presence of carcinogens
• Risk of Handling damage
• Tin Whiskers (Better to use within 6 months)
• Not Good for multiple reflow
• Difficult to inspect

7. Immersion Silver (IAg)

A good alternative to ENIG, with a moderate shelf life (about 12 months) and good electrical properties unmatched by other PCB surface finishes, but it is susceptible to sulfur dioxide, which tarnishes the surface and forms an AgS2 layer. This layer adversely affects solderability. To avoid this contamination, we package the PCB in silver-plated paper and sealed packaging.

Pros:

• Lead-free
• Excellent solderability
• Flat surface for fine pitch
• Sample processing
• Aluminum wire bondable
• Cost effective (than ENIG)
• Low high frequency signal loss (skin effect)
• Great Shelf life (6-12 months)

Cons:

• Tarnishes
• Silver Whiskering
• Sensitive to handling, electrical test, packaging
• Difficult to inspect
• Not good for micro-vias of ratio > 1:1
• Not suited for compliant-pin intertion (Ni-Au Pins)

Not sure which type of PCB surface finish is suitable for your PCB boards? Now is the time to contact us for a further manufacturability suggestion.

PCB Surface Finish Ultimate Guide- How To Choose The Most Suitable One

One of the most important aspects of the Printed Circuit Board (PCB) is the surface finishing. The type of finishing applied in PCB determines its efficacy as well as longevity. But with quite some options available, how do you determine the ideal one? Read on to find out.

 

Table of Contents

PCB Surface Finish&#;One of the most critical aspects of the Printed Circuit Board (PCB) is the surface finish. The finishing applied in PCB determines its efficacy as well as longevity. But with quite some options available, how do you choose the ideal one? Read on to find out.

1. PCB Surface Finish&#;What is PCB Surface Finish?

A PCB surface finish is the coating between the bare printed circuit board and a component. PCBs have copper finishes that are susceptible to oxidization and deterioration if left unprotected. To this end, it becomes necessary to apply finishing for two crucial purposes: 

&#; To protect the copper surface and circuitry

&#; To ready the surface for soldering associated components during assembly 

Now let&#;s take a look at the specific surface treatments and the differences between them.

2. PCB Surface Finish&#;7 Types of PCB Surface Finish & Comparison

There are seven types of PCB surface finishes, and each comes with its advantages and shortcomings:

HASL is the most common surface finish. It is also the most affordable. The application process involves dipping the PCB in a solution of molten solder and then blowing off the residue using a hot air knife. The resolution of molten solder is made of lead and tin alloys. 

Advantages

The most significant advantage of HASL surface finishing is that it is economical. Other advantages include:

• It allows for a larger processing window
• It applies to a wide range of PCBs
• The provides for excellent solderability

Disadvantages 

As mentioned, this surface finish involves dipping the board in a solution of molten solder made up of lead and tin. It makes it unsuitable for panels that demand RoHS compliance. This shortcoming is tied to other disadvantages that include:

• There is a difference in thickness between large and small pads
• Is not suitable for HDI products 
• It causes bridging on fine pitch 
• It is not suitable for BGAs and SMDs measuring less than 20mil in diameter
• Lead-Free HASL

Lead-free HASL is the most popular surface finish used on PCBs today. It is applied by immersing the PCB in a molten alloy lead, or tin alloy lead or tin alloy lead or tin alloy, which ensures that the entire surface is covered. Air knives are then used to blow off the residue for an even coating. 

Are you interested in learning more about pcb surface finish comparison? Contact us today to secure an expert consultation!

Advantages

One of the most significant advantages of lead-free HASL is that it exposes potential delamination issues by exposing the PCB to temperatures of about C. Other advantages include:

• Is widely available
• It is eco-friendly
• Ensures durability 
• It is re-workable
• It is affordable 

Disadvantages 

• May create thermal shock 
• It may result in uneven surfaces
• Is not ideal for fine pitching 
• It may bridge solders 
• It reduces PTH (plugged-through holes)
• Immersion Tin (ISN)

Immersion Tin is the ideal surface finish for fine pitch products, planar, backplanes, and press fit. ISN is applied by initiating a chemical displacement reaction with the PCB&#;s copper surface.

PCB Surface Finish&#;Advantages

Immersion tin comes with a wide range of advantages that far outweigh its shortcomings. They include:

• creates an even surface, unlike lead-free HASL
• It can be reworked 
• It can be substituted for reflowed solder 
• Is highly reliable
• It is ideal for a wide range of PCBs

Disadvantages

Tin and copper have a strong affinity toward each other. It means that the diffusion of one of these metals into the other is inevitable. The result is a shorter shelf life when compared to most other PCB surface finishes. It may also limit the PCB performance. It is its most significant shortcoming. Other shortcomings include:

• not ideal for PTH 
• Can be reworked, but to limited extents owing to its short shelf life
• It results in tin whiskering
• Can damage the solder mask 
• It is difficult to handle and can result in a wide range of damages
• It may be unhealthy for handlers as it contains a carcinogen known as Thoreau

Cost of Immersion Tin

&#; Immersion Silver (IAG)

Immersion Silver has been widely popular since the WEEE and RoHS directive was passed. It is considered an excellent alternative to ENIG for several reasons, chief among them being that it is ideal for fine pitch. Immersion silver is mainly used for aluminum wire bonding, membrane switches, and EMI shielding. 

Advantages 

One of the main advantages of immersion silver is that it contains OSP, which prevents tarnishing. However, this also makes it necessary for the PCB to be packaged immediately after application as OSP is sensitive to contaminants on the board advantages of immersion silver include:

It is compliant with RoHS directives and requirements

• Suitable for fine pitch 
• The moderate shelf life of about 12 months
• Highly stable when compared to other surface finishes
• Ideal for planar
• It is affordable and cost-effective

PCB Surface Finish&#;Disadvantages 

As mentioned earlier, the presence of OSP makes immersion silver susceptible to tarnishing, which is its most significant shortcoming. Other shortcomings include:

• It may result in silver whiskering
• It is not suitable for compliant-pin interaction as it has a high fraction co-efficient
• Some of its systems cannot throw into micro vias aspect ratios of 1:1
• Electroless Nickel Immersion Gold (ENIG) 

Electroless Nickel Immersion is fast becoming popular in the PCB industry as it overcomes many of the significant shortcomings associated with other surface finishes. ENIG has a two-part application process. First, a nickel layer is applied to serve as both a barrier to the copper and a suitable surface on which components can be soldered. Another layer of gold is then used to protect the nickel layer for the time during which the board is in storage. 

PCB Surface Finish&#;Advantages

The most significant advantage of ENIG is that it is ideal for the new and upcoming generation of complex surface components, including flip chips and BGAs; other surface finishes have shortcomings that limit their application in these new boards. Other advantages include:

• Is ideal for flat surfaces as the layers of nickel and gold as thin and even
• It does not contain lead
• Ideal for PTHs
• It has a long shelf-life

Disadvantages

houghAlthoughAlthoughAlthough ENIG has a long shelf-life, it has also been associated with the &#;black pad syndrome,&#; a common problem that leads to the buildup of phosphorus between the layers of nickel and gold, thus resulting in fractures well as faulty board connections. The only other major disadvantage is that it is not ideal for reworking.

&#; Nickel Palladium (ENEPIG)

Nickel Palladium (ENEPIG) PCB surface finishing is an upgrade of ENIG. In ENIG, immersion gold has been shown to destroy the layer of nickel. ENEPIG introduces a layer of plating palladium between the layers of gold and nickel.

Advantages

ENEPIG has been dubbed the &#;universal finish&#; because it applies to many modern, highly advanced boards with multiple surface packages. It comes with a range of advantages that include:

• It makes for a flat surface.
• Easy to process
• It doesn&#;t have a toxic effect on the skin. 
• It doesn&#;t contain lead.
• Ideal for multiple reflow cycles
• It is highly compatible with Sn-Ag-Cu solders.
• It has a long shelf life.

Disadvantages 

• It often results in the occurrence of black pad
• It reduces solder joint reliability
• The layer of palladium is too thick to support solderability performance
• Takes longer to wet compared to other surface finishes
• It is affected by plating conditions
• It is expensive compared to most other surface finishes
•  OSP (Organic Solderability Preservative)

OSP is an organic, water-based surface finish. It is selective in its bonding with copper, and it also makes the PCB solderable. 

PCB Surface Finish&#;Advantages

OSP surface finishing is notable for its environmental-friendliness since it is organic and water-based. It also makes it easy to apply, and the process is relatively short and straightforward compared to other surface finishes. Its advantages include:

• Provides an even, co-planar surface
• Requires low equipment maintenance
• It does not contain lead
• It is repairable 

Disadvantages

OSP is organic and water-based, makingngngng it quite sensitive to damages when handling. It is tied to several other shortcomings:

&#; It has a short shelf life

&#; It is terrible for PTH

PCB Surface Finish&#;How to Choose PCB Surface Finishes

The differences in these types of PCB surface finishes make them suitable and unsuitable for specific uses. To this end, anyone looking to apply the ideal surface finish should consider several factors:

&#; PCB Surface Finish&#;Pad Flatness

As mentioned severally, some surface finishes result in uneven surfaces that may impede performance, solderability, and other factors. If flatness is an important factor, consider surface finishes that have thin, even layers. Suitable options, in this case, include ENIG, ENEPIG, and OSP.

&#; Solderability and Wettability 

Solderability is always a crucial factor when working with PCBs. Specific surface finishes such as OSP and ENEPIG have been shown to hinder solderability, while others such as HASL are ideal for it.

&#; Gold or Aluminum Wire Bonding

If your PCB requires gold or aluminum wire bonding, your options may be limited to ENIG and ENEPIG.

&#; Storage Conditions 

As mentioned, some surface finishes such as OSP make PCBs fragile when handling while others improve durability. It should be considered beforehand when taking into consideration storage and handling requirements. Only when risk-free storage and handling requirements can be met, Surface finishes that make PCBs delicate should be applied. 

&#; Solder Cycles 

How many times will the PCB be soldered and reworked? As shown, many surface finishes are ideal for reworking. Others such as immersion tin, however, are not ideal for reworking. 

&#; PCB Surface Finish&#;RoHS Compliance 

RoHS compliance is crucial when determining the surface finish to go with. Usually, all surface finishes that utilize lead are not suitable for RoHS compliance and should be avoided.

Conclusion

As outlined, each type of surface finish has unique elements that set it apart from the rest. These elements make these finishes both suitable and unsuitable for specific applications, and the ideal option ultimately depends on the PCB&#;s makeup. 

At WellPCB, we have vast experience with PCB boards and surface finishes. Get in touch to learn more about the different types of PCB surfaces and more! We would love to help you come up with the ideal surface finishing for your PCB.

If you want to learn more, please visit our website lead-free hasl.