Join Us

How do you join diamond wire?

Author: Lily

Dec. 02, 2024

Steps to connect the diamond wire saw

Author&#;Huada Quarrying Machine FROM&#;Stone quarry machine manufacturer TIME&#;-05-18

Corediam are exported all over the world and different industries with quality first. Our belief is to provide our customers with more and better high value-added products. Let's create a better future together.

The diamond wire saw is a material used for the diamond wire saw to mine stone. Before the diamond wire saw starts to work, the diamond wire saw needs to be connected to the stone to be cut and the flywheel of the machine to perform the next step of cutting Work.

Diamond wire saw connection requires professional personnel to operate, the following describes the steps of diamond  wire saw wire connection.

The basic principle of diamond wire connection: the length of the bare steel wire rope at both ends of the rope = the length of the joint;

1. insert the two bare steel ropes into the special joint, and there should be no gap between the joint and the adjacent beads.

If you want to learn more, please visit our website concrete diamond wire saw ropes.

2.use hydraulic pliers special for diamond wire saws to buckle the joints tightly. When crimping, first place the middle part of the joint in the hydraulic tongs for crimping, and crimp it every 90°; then place the two ends of the joint in the hydraulic tongs in order to crimp; finally, place the middle part of the joint in the hydraulic crimping again;

3. check the joints after the crimping is completed, and then use an angle grinder to remove the flash and burrs.

The above are the steps of connecting the diamond wire saw to everyone.

DIY wire saw designed to slice up a forklift | Page 3

woodchucker said:

do you have to reverse? is there no way to braid the line together like they do for eye's on big steel cables, and on ships lines? where you open the wire and braid it together. I know it will be thicker, but how do they do it for the professional machines?

Click to expand...
I exhausted myself trying to think of ways to do a continuous loop prior to going down this route and now (for this revision at least) I'm committed to the reversing. In the semiconductor industry where the wire I'm using comes from, I believe even they do it by reversing.

Subsea and mining operations both use the same kind of wire but they differ in how they join the ends to make a continuous loop. They both use wire that is a steel wire rope (steel "cable") that has diamond-sintered beads threaded onto it, and those beads are separated by springs and then crimped onto the cable. Usually rubber is extruded over all of this, but not always.





In the case of mining, the wire ships from the manufacturer on a spool with two free ends just like any other wire/cable. The operators onsite cut the wire to the length they need and then crimp the two ends together with a swivel joint that is something like universal/cardan joint.




Because the crimp connector is smaller diameter than the diamond beads, it doesn't get hung up in the cut.

For subsea operations, the wire is manufactured custom order for the specific loop size you require for your tool, as an actual continuous loop. They do in the way I think you were referring to, similar in concept to how a flemish eye works:


They will separate the 7 main strands of the inner cable and cut each one some distance (ex: a foot) longer than the last, on both ends, thread the beads over it and compress the springs, then weave the two ends of the cable together with one another such that their 7 staggered cuts butt up to each other in 7 different spots. Then they release the springs and space the beads out evenly around the loop, and crimp the beads. This loop is extremely difficult break.

Joining the ends of 0.3mm wire without creating any kind of knot is (unless there is something I've never heard of) effectively impossible. I worked with some resistance welders in the wire & cable industry that could join the ends of copper wire together but this was much larger diameter wire and the joint was not perfect. It had to be filed down by a person after. I can't imagine doing it to 0.3mm wire.

The most workable idea I had was to make a continuous loop of single strand wire by wrapping it around itself at a set interval as you make the loop, and go over it several times (7 times maybe? Like a wire rope?) like I've done here with twine:


The ends of the wire could be tucked into the interior of the "cable" and secured there somehow (solder?). But I think this would not work for the following reasons:
  • Most of the diamond coated surface is unused, buried inside the bundle/cable.
  • Those diamond coated surfaces on the interior will be abrading each other as the cable flexes. It would probably chew itself up from the inside out.
  • The ends of the wire would probably find their way out of the interior of the bundle and get hung up in the cut.
  • The "cable"/bundle would have no inherent internal support. No incentive to remain round like a cable. As it gets into a slot cut by itself, it will probably want to flatten out like a tapeworm.

If you have other ideas I'm glad to hear them, but I probably won't try them until later, as I've already gone past the point of no return in this specific direction.

I exhausted myself trying to think of ways to do a continuous loop prior to going down this route and now (for this revision at least) I'm committed to the reversing. In the semiconductor industry where the wire I'm using comes from, I believe even they do it by reversing.Subsea and mining operations both use the same kind of wire but they differ in how they join the ends to make a continuous loop. They both use wire that is a steel wire rope (steel "cable") that has diamond-sintered beads threaded onto it, and those beads are separated by springs and then crimped onto the cable. Usually rubber is extruded over all of this, but not always.In the case of mining, the wire ships from the manufacturer on a spool with two free ends just like any other wire/cable. The operators onsite cut the wire to the length they need and then crimp the two ends together with a swivel joint that is something like universal/cardan joint.Because the crimp connector is smaller diameter than the diamond beads, it doesn't get hung up in the cut.For subsea operations, the wire is manufactured custom order for the specific loop size you require for your tool, as an actual continuous loop. They do in the way I think you were referring to, similar in concept to how a flemish eye works:They will separate the 7 main strands of the inner cable and cut each one some distance (ex: a foot) longer than the last, on both ends, thread the beads over it and compress the springs, then weave the two ends of the cable together with one another such that their 7 staggered cuts butt up to each other in 7 different spots. Then they release the springs and space the beads out evenly around the loop, and crimp the beads. This loop is extremely difficult break.Joining the ends of 0.3mm wire without creating any kind of knot is (unless there is something I've never heard of) effectively impossible. I worked with some resistance welders in the wire & cable industry that could join the ends of copper wire together but this was much larger diameter wire and the joint was not perfect. It had to be filed down by a person after. I can't imagine doing it to 0.3mm wire.The most workable idea I had was to make a continuous loop of single strand wire by wrapping it around itself at a set interval as you make the loop, and go over it several times (7 times maybe? Like a wire rope?) like I've done here with twine:The ends of the wire could be tucked into the interior of the "cable" and secured there somehow (solder?). But I think this would not work for the following reasons:If you have other ideas I'm glad to hear them, but I probably won't try them until later, as I've already gone past the point of no return in this specific direction.

For more diamond saw blade for stone cutting manufacturersinformation, please contact us. We will provide professional answers.

14

0

Comments

0/2000

All Comments (0)

Guest Posts

If you are interested in sending in a Guest Blogger Submission,welcome to write for us!

Your Name: (required)

Your Email: (required)

Subject:

Your Message: (required)

0/2000