5 FAQs about grinding abrasives

Grinding abrasives require the right guidance about how to store, test, and use them; otherwise, a routine grinding application can turn into a safety nightmare. Sparks, airborne debris, and a disengaged, detached wheel can all present safety hazards to you and those around you. Improper use also can cause the grinding wheel to break, which can result in operator injury.

SINOTOOLS are exported all over the world and different industries with quality first. Our belief is to provide our customers with more and better high value-added products. Let's create a better future together.

No matter how much times passes or how much technology evolves, you still need to do your research to ensure your shop is following all appropriate safe grinding and finishing practices and procedures.

Here are the answers to the top five most frequently asked safety-related questions.

1. Does a Grinding Wheel Have an Expiration Date?

Resin-bonded wheels, including portable wheels, should be used within two years from the date of manufacture. This assumes you&#;ve stored the wheels according to the manufacturer&#;s recommendations. While it may be possible to use resin-bonded wheels after the two-year mark when they are stored properly, you should always examine any wheels more than two years old. Consider having older wheels inspected or speed-tested to determine if any degradation is present.

To help improve shelf life, store wheels in a dry, protected area free from extreme variations in temperature and far away from solvents. Establish a storage system that encourages you to use your oldest wheels first. And never leave a wheel attached to a tool overnight.

2. Can I Ring-Test a Resin-Bonded Wheel?

Experienced operators know that a safe grinding operation begins long before the machine is turned on. Before you ever mount a wheel, you must give it a visual inspection and put it through a ring test to ensure that it is not damaged.

Experienced operators know that a safe grinding operation begins long before the machine is turned on. Before you ever mount a wheel, you must give it a visual inspection and put it through a ring test to ensure that it is not damaged.

OSHA, ANSI, and most grinding wheel manufacturers require ring testing before the wheel is mounted on a grinding machine. Vibration is the key to the ring test. When the wheel is struck, it vibrates at a certain frequency and emits a sound, much like a tuning fork. Any nonuniformity in the wheel will change the vibrational response and, consequently, the sound. When the nonuniformity is a structural flaw, like a crack, the ring test will produce a dull sound, alerting the operator to a problem.

However, some wheels cannot be ring-tested because of their size or construction.

Resin-bonded wheels are difficult to ring-test because of their natural vibration-dampening characteristics. When struck, this wheel does not produce a clear tone like vitrified wheels do, making it hard to discern if it&#;s cracked. It takes a quiet environment and a well-trained ear to ring-test a resin-bonded wheel properly. Further, resin-bonded wheels that contain fiberglass reinforcement cannot be ring-tested as they will never produce a clear ring. Portable wheels for angle grinders fall into this category.

3. How Often Should I Check the Speed of My Tool?

Grinding wheels are designed to be operated at certain speeds. Exceeding recommended speeds can cause wheel breakage, risking injury to you and others nearby. So be sure to check the wheel and machine's rated speed every time you mount or remount a wheel to make sure it isn&#;t operating in an overspeed condition.

Featured content:
How Does the Cordless Electric Drill Work?

If you want to learn more, please visit our website abrasive grinding wheel manufacturers.

The abrasive wheel's maximum operating speed is marked on the wheel, and the machine's normal operating speed is marked on the machine. Never exceed the wheel's maximum operating speed as stated in revolutions per minute or in surface feet per minute. Failure to comply with this requirement is not only very dangerous, it is a violation of ANSI safety requirements and OHSA law.

4. Does It Matter Which Way the Flanges Go on a Right-Angle Grinder?

The orientation of the flanges plays a key role in mounting cutting and grinding wheels. The back flange is keyed to the machine so it can go on only one way. With most angle grinders, the outer flange can be used either way, but it depends on the wheel thickness.

For thin cutoff wheels, the recess side of the outer flange should be against the wheel. This allows the flange assembly to be tightened to the point where it holds the wheel, preventing slippage. For thick grinding wheels, however, the hub side of the outer flange should be against the wheel. This configuration allows you to tighten the flange assembly to hold the wheel properly.

5. Do I Need to Use a Guard With a Coated Abrasive?

The idea that coated abrasives do not require guards is simply not true. ANSI B7.7, Safety Requirements for Abrading Materials with Coated Abrasive Systems, states: &#;If the machine is designed and equipped with guards, it shall not be operated without the guards properly installed and in place. Safety guards shall be properly installed and in place on any machine used in grinding. Guards prevent operator exposure to the drive mechanism and the moving coated abrasive product, help contain grinding swarf and any flying debris in case of breakage, and are often part of the dust collection system.&#;

When operating a right-angle grinder, you must have the guard in place. When using a portable sander, a guard is optional unless the tool was originally equipped with one. Never remove a guard provided by the machine manufacturer for any reason. It is there to keep you safe.

Grinding wheels are discs that contain abrasive particles and grains that have been bonded together to form a wheel shape. Although the disc format is the most common shape, they can also be made in the shape of cones or cups.

Grinding wheels are attached to grinders or saws and rotated at high speeds for a variety of tasks. The abrasive grit and grains in the wheel are able to grind or cut through hard materials such as metal or steel. The abrasive grains are bonded together by either organic or inorganic substances.

Inorganic grinding wheels are fitted in a furnace and have a hard yet brittle structure that holds its form during precision cutting. These wheels usually require dressing before use to straighten the wheel or to form it into a desired shape.

Organic grinding wheels are cured at low temperatures, are shock resistant and do not require dressing. They are commonly used for cutting or grinding work that does not need to be precise.

They are categorised according to characteristics such as grit size, the bonding used, the abrasive material, the grade of the grinding wheel and the wheel&#;s structure.

Are you interested in learning more about plier and cutter manufacturer? Contact us today to secure an expert consultation!